Nano-MOUDI, M100, M110 and MOUDI II for Asia, Europe, Canada, USA, Central & South America

REQUEST A QUOTE

CALL US: 720-635-3931


Applied Physics, Inc.

Applied Physics, Inc. supports

MSP Corporation Products

Nano-MOUDI Cascade Impactor

General Discussion - Request a Quote

The MSP Corporation MOUDI 100 and Model 110 Cascade impactors consist of 8 or 10 impactor stages connected in series with smaller and smaller cut-point diameters. Designed for low concentration aerosols, the MOUDI 100 and 110 cut-off diameters in each stage depend on the air velocity and geometry of the stage (i.e. the distance from the nozzle to the impaction plate). The MOUDI 110 impactor has cut-point stages of 10um, 5.6um, 3.2um, 1.8um, 1um, 560nm 320nm, 180nm, 100nm, 56nm @ 30 lpm inlet flow with final filter and single stage pre-impactor of 18um. This gives the opportunity to analyze (e.g. chemical or gravimetrical) a number of small size intervals.

Some drawbacks of poorly designed conventional impactors are the risk of “bounce off” from one stage to the next (i.e. particles of wrong size at a different stage) as well as the problem of obtaining sharp cut-off diameters in the last stages (cut-off diameter less than 0.1 – 0.2 mm). Coating the impaction plates with oil or some other sticky substance, which catches the particles more effectively, can reduce the risk of bounce, but will severely complicate direct mass concentration calculations of the different stages. MOUDI Cascade Impactors are designed with superb cut-point resolution across the entire size range of 10nm to 18um with minimal bounce at each stage. The non-rotating, Nano MOUDI (see below discussion) provides sharp cut-points at 32nm, 18nm and 5.6nm at equally high resolution. 

The new 125B Rotating MOUDI, designed for high concentration aerosols, is provided with all 13 stages and very sharp cutpoints, very low bounce response, digital controls and flow meters, all in one product.

FEATURES & APPLICATIONS - Request a Quote

Model 100, 110 & 115 MOUDI
  • Precision size classification of aerosols for
    - air pollution
    - pharmaceutical aerosol drug delivery
    - diesel blow by and engine emission testing
    - automotive airbag testing
    - industrial hygiene studies
  • Sharp cut-point characteristics
  • Four equal geometrical intervals per decade of particle size
  • Models 100 and 110
    - 30-L/min sampling flow rate
    - 8 and 10 impactor stages + after filter
    - 0.18µm and 0.056µm minimum cut-point
  • Model 115
    - 10-L/min sampling flow rate
    - 3 impactor stages + after filter
    - 32, 18 and 10nm minimum cut-point

Model 100 & 110 MOUDI Cut-Point Performance
 
Model 100 & 110 Nano-MOUDI Cut-Point Performance

MOUDI Impactor Specifications - Request a Quote

(Subject to change without notice)
  Model 100 with rotator Model 110 with rotator Model 110 -1    w/o
rotator
Model 125 B
with rotator
Model 115 w/o rotator*
Impactor stages 8 10
10 13 3
Flow rate, L/min 30 30 30 10 10
Cut-points, µm 18, 10, 5.6, 3.2, 1.8, 1.0, 0.56, 0.32, 0.18 µm
18, 10, 5.6, 3.2, 1.8, 1.0, 0.56, 0.32, 0.18, 0.1, 0.056 µm 18, 10, 5.6, 3.2, 1.8, 1.0, 0.56, 0.32, 0.18, 0.1, 0.056 µm 18um, 10, 5.6, 3.2, 1.8, 1.0, 560nm, 320, 180, 100, 56, 32, 18, 10nm 32nm, 18nm 10 nm
(D x H) 80 x 420 mm 220 x 560 mm 220 x 560 mm 220 x 660 mm 80 x 190 mm
Weight 11 kg (24 lb) 12 kg (26lb) 2.3 kg (5.1 lb) 14 kg (29lb) 1.8 kg (4 lb)
Power 115 VAC, 60 Hz, 0.3A  115 VAC, 60 Hz, 0.3A 115 VAC, 60 Hz, 0.3A  115 VAC, 60 Hz, 0.3A  
Optional 230 VAC, 50 Hz, 0.2A  230 VAC, 50 Hz, 0.2A 230 VAC, 50 Hz, 0.2A  230 VAC, 50 Hz, 0.2A

*The Model 115, 3-stage Nano-MOUDI™ is available in a non-rotating version only. The Model 115 and Model 125 requires a separate 6 CM/H vacuum pump (NAN-090) to operate.

Model 115, Nano-MOUDI Cascade Impactor - Request a Quote

The principle of operation of the Nano-MOUDI is the same as that of the MOUDI™ impactor. It classifies particles according to aerodynamic size by inertial impaction in several multi-nozzle stages stacked in series.

The design configuration chosen for the nano-MOUDI adds three stages to the standard 10-stage MOUDI™. The cut sizes of these stages follow the four cuts per decade of particle size progression of the standard MOUDI™. Therefore, the cut sizes are 32nm, 18nm and 10nm. The absolute pressure after the last stage of the standard 10-stage MOUDI™ is about 0.60 atm. By adding three stages, the absolute pressure at the stages will become low enough so that the volumetric flow will be larger than the flow that can be pulled through a micro orifice nozzle plate. Therefore, the flow rate through the nano-MOUDI stages is decreased to 10 lpm (the flow rate in the standard MOUDI™ is 30 lpm).

The design parameters for the nano-MOUDI stages are shown in Table I, along with the same parameters for the standard MOUDI™. Note that the Reynolds Number is generally in the range of 500 to 3,000, the desired range for impactor operation1. However, the Reynolds Number of the final stages are somewhat lower than this range. Also note that the value of the pressure at the last stage is about 0.12 atm. Although this is a rather low pressure, it is substantially higher than that for a low pressure impactor which has pressures on the order of 0.03 atm for cut sizes of 0.05 µm. Corresponding pressures for the MOUDI™ at that large of a cut size is 0.60 atm.
 
Model 115 & 125 Nano-MOUDI Cut-Point Performance

Features & Applications

Model 125B Rotating MOUDI, Model125A Non-Rotating
  • Precision size classification of aerosols for
    - air pollution
    - pharmaceutical aerosol drug delivery
    - diesel blow by and engine emission testing
    - automotive airbag testing
    - industrial hygiene studies
  • Very Sharp cut-point characteristics with little bounce from each stage
  • - 10-L/min sampling flow rate
    - 13 impactor stages + after filter
    - 18um, 10, 5.6, 3.2, 1.8, 1.0, 0.56, 0.32, 0.18, 0.1, 32nm, 18nm, 10nm cut-points
  • Rotating (Model 125B) and Non-Rotating (Model 125A) products available